Single-Storey House (Sophia) - 21 m2 + 6 m2

TECHNICAL DATA

Snow load

80 kg/m² - TS 498 and TS EN 1991-1-3

Wind speed

102 km/hour (50 Kg/ m² ) TS 498 and TS EN 1991-1-4

Exterior wall heat transfer coefficient

K: 0,48 Kcal/m² hC ( K: 0,56 W/m² K )

Interior wall heat transfer coefficient

K: 0,46 Kcal/m² hC ( K: 0,53 W/m² K )

Roof heat transfer coefficient

K: 0,39 Kcal/m²hC ( K: 0,45 W/m² K )

Frame load capacity

200 kg/m² (for two-storey buildings) T.S 498

According to TSE 498 could be 200 / 350 / 500 Kg/m2

Earthquake zone

Effective ground acceleration coefficient :Ao=0,40 (1.degree earthquake zone )

Building Importance Coefficient ( I =1) according to building purpose and type of use.

Moving Load Participation Coefficient (n = 0,3)

I =1 / 1,2 / 1,4 / 1,5 , should be calculated as n=0,3 / 0,6

according to building purpose and type of use.

RELATED STANDARDS

DESIGN-STATIC : TS EN 1993-1-1, 1-2, 1-8+AC, EUROCODE 3, TS 11372, TS 498 , TS 648, TS 6793, TS EN 1991-1-1-3 , 1-1-4 (EUROCODE 1), TS EN 1998-1 (EUROCODE 8), IMO-01.R-01/2005, Regulation Regarding Buildings to be Built in Earthquake Zones-2007

PANEL CARCASSES, TRUSS, PURLIN STEEL CONSTRUCTION :

Material : DX51D+Z (~St 37) Erdemir quality no 1311, S250GD+Z Erdemir quality no 1325, S320GD+Z Erdemir quality No 1332 , S350GD+Z (~St 52) Erdemir Quality No

1335, standard DIN EN 10346-00, building steel galvanized by zinc coating

Production : Galvanized C / U sectioned cold formed profile compatible to JIT production system in TS EN 10162 standards and extruded from rollformer machine,

in 0,8-2 mm steel sheet thickness and 40-300 mm web width.

Juncture components : Clinch nut, galvanized bolt, nut DIN 960-961,DIN 935-F,8.8

Heat Insulation : Regulation of Heat Insulation (8.05.2000)

Sound Insulation : TS 187 and TS 854 (DIN 4109)

Fire Resistance : DIN 4102 Regulation Regarding Protection of Buildings from Fire - 2002

Climate Region

Wall insulation proper for 2nd climate region ( K:0,60 W/m² K ).

Roof insulation proper for 2nd climate region ( K:0,40 W/m² K ).

Concrete should be poured in compliance to concrete planning (foundation dimensions) which will be given by Barelit Ltd. EMPLOYER shall fulfill designs, static calculations of the foundation and coating of foundation and floor. Building is fixed on the concrete floor with anchorages and dowels. Raft foundation with iron or steel reinforcing mesh foundation should be prepared on the

hardened substrate

EXTERIOR and

INTERIOR WALLS

2537 mm

1250x2537x80 mm and 1250x2500x80 mm

8 mm fiber cement plain board – (Incombustible) A1 class

Interior Wall Surfaces

8 mm fiber cement plain board – (Incombustible) A1 class

(10-12-14 mm thick fiber cement boards are used on the surfaces optionally.)

60 mm thick polystrene foam ( EPS ) - fire class B1 (16 kg /m3)

Vertical Records 64x50x1,2 / 1,0 mm galvanized C / U sectioned high standard cold formed profile extruded from rollformer machine (changes between 0,8 - 2 mm according to static calculations and as required by the construction.) EPS material is placed inside panel carcass against loss of heat.

CEILING COATING

8 mm fiber cement board –(Incombustible) A1 class

80 mm blanket Glasswool

ROOF

Onduline (shingle, metal briquette or painted galvanized steel sheet can be produced optionally) Black sponge is used under eaves and ridges for insulation

Cold-formed profile extruded in rollformer machine from angular omega sectioned (80x50x0,9 mm ) galvanized rolled steel sheet. ( wooden purlins are used in onduline coated roofs

Exterior and interior profiled special design steel struss in spaces of 125 cm produced from high standard galvanized rolled steel sheet (thickness of steel sheet changes between 0,8-2 mm according to static calculations and construction requirements) 150x300 mm pvc culvert on exterior fore trusses for ventilation.

20 cm PVC eaves.

150x150 mm pvc culvert to prevent from transpiration.

PVC eaves trough

SYSTEM

Consists of panel carcass, mezzanine fram, roof trusses and purlins and diagonals in galvanized rolled steel sheet in S350GD+Z (1335 ) quality (~ St52 ) or DX51D+Z (1311 ) quality (~ St37 ) extruded from rollformer machine. If required, profile wall thickness and width can be changed or industrial profiles and DKP/Galvanized column-beam reinforcement and welding/screw/bolt can be used as a result of static calculations.

Building-Wall junctures are connected with bolts and nuts and PVC H building profiles are used for impermeability. (Jointless wall aplication is realized by using joint tape in place of PVC H as an option.)

CEILING JOINTS

8 mm fiber cement ceiling material is jointed by using galvanized steel sheet and PVC omega, PVC sheath and painted aluminum T profile (to prevent from transpiration).

(8 mm Fiber cement Suspended Roof, 6*600*600 mm Fiber Cementlam Suspended Roof, Rockwool Suspended Roof-Perforated

Aluminum Suspended Roof and components are applied optionally.)

ACCESSORIES

Edge omega, omega over panel, tympan edge coating material, tympan coating material, window rough bucks, coating material for underneath the eaves is PVC (to prevent from corrosion and transpiration).

NOTE: Edge omega, omega over panel, window rough bucks, tympan steel sheet are produced in galvanized steel sheet acording to building static and construction.

DOOR PROFILES

Exterior door frame

Aluminum or steel door

Interior door frame

mdf lam press door or American type door

Door of wet volumes

mdf lam press door or American type door

Door lock and handle

Exterior and interior doorlocks cylindirical (interior doorlocks of housing are mortise locks) ( ITO or KALE Brand ), door handles are gold or grey metal.

WINDOW PROFILES

Window (PVC framed)

830/1190 mm, handles in PVC

Fanlight (PVC framed)

830/ 400 mm, Handles in PVC

Double Glass

4+9+4 mm – SISECAM Brand

PAINT

Exteriors

2 coat Silicone based exterior paint

Interiors

2 coat Plastic based interior paint

Other

Galvanized cold form truss, purlin, panel carcass, mezzanine frame are without primer as weldless technology is used.

Note: Paint color should be informed by the customer one week before the shipment,the latest. Otherwise, standard paint colors will be delivered.

Metal components not galvanized

1 coat rapid primer+Exteriors 2 coat oil paint

ELECTRICAL

INSTALLATION

Surface or Flush

mounted

Cable

(NYM ,220 Volt , 50 Hz.)

Antigron cable inside MUTLUSAN PVC cable duct (16 mmx25 mm )

Socket outlet 3X2.5 mm² NYM, Socket lines 4X2.5 mm² NYM cable

Lighting outlets 2X1.5 mm² NYM, lines 3X1,5 mm² NYM cable , VATAN, OZNUR

or OZLER Brand

Lighting Armatures

House

Fluorescent TMS Armature, Fluorescents GENERAL Brand, Armatures

PELSAN or BALKAYA Brand

Glop - IP 44, BALKAYA or PELSAN Brand

Sockets, Switches

VIKO nemli yer Brand or equivalent

Fuses, fuseboxes

W automatic fuses GENERAL Brand, SIEMENS Brand

Fuseboxes VIKO or MUTLUSAN brand

Power panel, Weak current installations

(Telephone,TV, data), Mainline connections

Will be fulfilled by the Employer company.

SANITARY

INSTALLATION

Surface or Flush

Mounted

Sanitary Ware / Armatures

(Pedestal wasbasin 45*55 cm. optional )

KUTAHYA SERAMIK Brand

and shower

faucets

Faucets are mounted on the wall in cold water installed washbasins, faucets ate outlet from the washbasin in hot water installed washbasins.

Ceramic flush tank WC (flush wc)

Squatting toilet (bidet faucets ECA YAK Brand)

ACRYPOL Brand

Pipes

Ground should be prepared compatible to concrete planning which will be given by Barelit Ltd. It is EMPLOYER company's responsibility if explanations in the concrete planning are not taken into consideration.