Shunan Fine Grain Grout Joints 3-10mm Grey - SA817

Shunan high-performance flexible cementitious grout for ceramic tiles with joints from 3 to 10 mm

anti-weathering formuladurable, polymer modified water-repellent cement based grout for internal and external use on walls and floors. For joints up to 10mm wide.

Suitable for commercial and domestic kitchens, showers, bathrooms, showers, conservatories, balconies, terraces, underfloor heating and timber floors. Flexible grey powder cementitious grout consisting of hydraulic binders, inert fillers of selected particle size, polymers, organic additives and pigments.Suitable for grouting floors or walls in interiors or exteriors clad with any kind of ceramic tile, natural stone or vitreous mosaic with joints between 3 and 10 mm wide.Suitable for surfaces subject to intense traffic or particularly.

Standard: JC/T 1004-2006

water addition:0.23 liter/kg powder

Grout for joints 3-10 mm wide in facings of ceramic, clinker, natural stone tiles gres (stone ware) etc.

• Fine-Grained
• Water Repellent
• Frost Resistant
• Elastic
• Contains light resistant pigmentsfor horizontal and vertical surfaces
• Easy to Maintain
• Very Dense
• High Resistance to Contamination
• High Resistance to Fungicides

Cement based, polymer strengthened grout for floor and wall, inside and outside, in wet and dry rooms

• Flexible floor and wall grout in lightfast colours
• No risk for discolouring
• Special applicable for wet rooms and intensive care
• Special applicable for non – absorbing tiles
• Secure uniform hardening on non – uniform tile quality

Consumption:

• (dependant on tile dimensions and joint width): 2 – 4 kg/m2

Consumption =(A+B)*C*D*1.5/(A*B) mm

A- length of tile B- width of tile C- thickness of tile D- joint width

Shunan tile grout gives a more dense and compact joint with minimal risk for bacteria penetration. The grout resists intensive cleaning without giving colour rub-off effect and can though be special recommended to wetrooms.
Shunan SA817 is a dry product, which can be used after mixing with water. The grout is easy to work with and the joint is easily filled. Shunan grout is supplied in many fastlight colours. See colour card.

Cement based, polymer strengthened, quick hardening, flexible, frostsafe and waterfirm grout in powder form.

Application areas

• For grouting of tiles/ceramic clinker on floor and walls, indoor and outdoor, in wet and dry areas.
• The risk for bacteria penetration by capillary absorption in the dense and compact grout is minimal.
• The joint withstands hard loading and intensive cleaning. supecolour is therefore very applicable in all wetrooms.
• Joint width 3 – 10mm.

Tile types

• can be applied to all types of ceramic tiles and natural stones, special applicable for low absorbing and non – sucking tiles.

Pre-treatment of substrate

• Joints and tiles shall be clean, free from dust, oil, dirt, grease and the like.

Application

• 25kg powder to be mixed with 5.5 – 5.9 litre of clean water. Use a glue mixer on a slow revolving hand drilling machine in order
  to avoid mixing air into the grout. Make sure powder, water and substrate are within the recommended working temperature.
• Mix 2 – 3 minutes to a lump free mass.
• The grout is now ready to use and can be applied within 1 – 2hours after mixing.
• The grout shall be worked properly into the joint with a rubber spatula or grouting trowel, which is drawn diagonally over the joints. When the grout in the joint is surface-dry but still workable, the excess grout on the tiles shall be loosened with a moistened padmaster/sponge. The tiles surface is then cleaned with hard wringed sponge/wash boy and the grout is finally shaped.
• The grout is after polished and water-film and grout-slurry removed.
• The grout shall be kept moistened for 2 days in order to prevent forced drying.
• After 2 days the joint can be cleaned for possible hardened grout slurry using ceramic cleaner.
• Dependant of the suction ability and room temperature the grouted tile surface can withstand light walking traffic/load after 3 – 6 hours and maximal loading after 7 days.

Industrial safety

• The product contains cement. Working hygienic rules for cement shall be followed.
• Reference to product safety data sheet.

Storage and transportation

• Transport and store dry. Storage period minimum 6 months from production date in unopened packingTechnical data
• Application time: 1-2 hours
• Drying time at 18°C
  for light walking traffic/ loads: 3-6 hours
  Ready for full load: 7 days
• Lowest working temperature: 6°C
• Recommended working temperature: 10-20°C

Physical Property

· Ensure 24 hours of time interval after tiling

· Before grouting, make sure that the tiles joints are clean without water