Shunan Adhesive for Facing Stones - SA814

For fixing ceramic,porcelain and natural stone tiles:, low porosity tiles or substrates,tiling onto existing tiles,walls&floors - details see: https://www.buildingsupplieshub.com/shunan-adhesive-for-facing-stones-10082853

Place of Origin: Shanghai China (Mainland)	Brand Name: Shunan	Model Number: SA814	Usage: Joint Mortar,Building construction
Type: Cement Mortar	Composition: Cements and additives, sand, polymers	Color: Grey or White	Quality System Standard: ISO 9001:2008

contact supplier for Shunan Adhesive for Facing Stones

Shunan. SA814 natural stone tile adhesive for walls & floors

Can be used with most tile types including porcelain and natural stone

Packaging

Weight: 40kg
Color: white
Standard:GB24264-2009
Shelf life: 6 months from production date
Storage: unopened bag on plate in dry place

Field of Application

.Used to fix natural stones, which thickness is less than 20mm when fixed on wall

·Used to fix natural stones both on inside and outside walls and floors

·Stone fixed on wall higher than 3.5m suggested to be fix with mechanical anchor together

·Used for fixing tiles in dry and damp area

Consumption

7~10 kg/m², dependant on the stone types and adhesive density

Application properties

1) Water addition: 0.23 liter/kg powder (9.2 liter /40kg)

Add water to the mix until you have an adhesive the same consistency as peanut butter.

2) Joint thickness: 5-7mm

3) Adjust time: 10-15 min

4) Pot life: 4 hours

Technical Information

Items		Ordinaryground	Full load ground and the wall
Ordinary type	Tensile adhesive Strength ≥	0.5 N/mm²	1.0 N/mm²
	Tensile adhesive strength after soaking ≥
	Tensile adhesive strength after heat aging ≥
	Tensile adhesive strength after freeze-thaw cycles ≥
	Tensile adhesive strength after 20 min open time ≥

Substrate requirement

The substrate should be hard, sound, dry, flat, clean and durable

Substrate preparation

Substrate should be flat ,hard, level, dry, and clean with normal absorption
Clean the surface until free of grease, dust or any stains
Old paint or plaster should be removed
Substrate been repaired should be preserved at least 48 hours

Mixing:

Using a mechanical mixer, add 25kg Shunan glass block mortar to 5.75 litres clean water while mixing. Mix well to a creamy, lump-free consistency. Let the mix stand for 3 - 5 minutes before stirring again. Use within 5-6 hours (20°C).

Processing:

1. Apply the mix to the surface using a notched trowel for tiles, the mix can be applied in bed thicknesses between 5 - 7mm, coverage is approximately 5 -10kg/m2, actual coverages will be determined by site conditions, workmanship, etc)

2. Apply only as much adhesive as can be tiled in 10-15 minutes to prevent the adhesive from “skinning” before the tiles are applied

3. Bed tiles firmly using a rubber mallet. When tiling exterior walls ensure the tiles is in full contact with the adhesive. Occasionally, life a block to ensure that there are no air pockets. Never fix tiles using the ‘spot’ method.
Application Environment:

1. Ambient temperature: 5°C~35°C

2. Avoid application if too hot or freezing weather

3. Avoid application under direct sunlight and strong wind

Safety:

May cause serious damage to eyes
May be sensitive to skin in case of contact. lrritable for eyes, respiratory system and skin
Keep out of the reach of children
Avoid breathing the dust
In case of contact with eyes,rinse eyes immediately with plenty of water and consult a doctor
Wear suitable protective clothing,gloves and eye / face protection

Packaging Detail:Packed in 40kg plastic lined paper sacks

Delivery Detail:5 days